Just How to Remove as Well as Change a Tub
Just How to Remove as Well as Change a Tub
Blog Article
The article author is making a few good annotation about Installing A Bathtub overall in this article just below.
Mounting a tub isn't precisely rocket science, but it does call for strong plumbing, woodworking, and sometimes, tiling abilities. Changing an old tub with a new one is additionally a reasonably tough project. If the old bathtub is conveniently obtainable, the job can relocate rapidly; if you have to open a wall surface to get rid of the old bathtub as well as position the new bath tub, the job is a lot harder. In either situation, the project is within a home handyman's abilities, although you will certainly need a helper to move out the old bathtub as well as set in the brand-new one. Make certain you have qualified yourself for the job and also fit attempting it. Rather than working with a service provider to take control of a halfway-completed job, it is far better to think about employing one prior to you start. Opportunities are you may need an expert plumber to make tube connections.
This write-up will certainly aid you set up a new tub in your restroom if you have actually already gotten a new tub and don't require to change the setup of your previous water pipes.
Your tools and product list must consist of the following:
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your setup, after that the first thing you need to do is detach the supply of water. After doing so, activate the faucets to drain any type of water staying in the system. The process of removing the existing taps can be quite problematic because of the restricted gain access to that is usually the case.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the taps. Have a fabric prepared for the remaining water that will originate from the pipes. Once the supply pipes have been eliminated, make use of the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary faucets from turning throughout this process. When the taps have been gotten rid of, the holes in the bath/basin will need to be cleaned of any type of old securing substance.
Before carrying on to fit the brand-new taps, compare the pipeline links on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is required for the brand-new faucets to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will need a plastic port to stop damages to the thread. One end of the connector fits on the plastic tail of the tap as well as the various other end gives a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly need minimizing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, place the faucet in the installing opening in the bath/basin making sure that the washing machines are in location between the tap and the sink. Secure the tap in position with the supplier given backnut. As soon as the faucet is safely in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with regular tap connectors. The previous kind ought to be connected to the faucet finishes first, tightening up only by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Mounting the Bathtub
Making use of the two wood boards under its feet, put the bath tub in the needed position. The wood boards are helpful in uniformly spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto four tiny points.
The following goal is to make sure that the bath tub is leveled all round. This can be achieved by inspecting the level and changing the feet on the bath tub till the spirit level checks out degree.
To install taps, fit all-time low of the outermost adaptable faucet connector to the suitable supply pipe by making a compression join; after that do the exact same for the various other faucet.
Activate the water supply and check all joints and new pipework for leaks as well as tighten them if needed. Fill up the tub as well as additionally examine the overflow electrical outlet and also the regular electrical outlet for leakages.
Ultimately, fix the bath paneling as defined in the maker's user's manual. Tiling as well as sealing around the bathtub needs to wait till the tub has been used at least when as this will certainly settle it right into its last setting.
Preparing for the Installation
To start with, the sustaining framework supplied with the bath needs to be fitted (if called for) according to the producer's instructions. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is necessary to make certain that if the tap features a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets unit to stop strain on the bath tub.
Fit the versatile faucet ports to the bottom of both taps making use of 2 nuts as well as olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet with the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Ensure you make use of all of the provided washing machines.
Connect the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bath need to now be ready to be suited its last position.
Tiling Around the Tub
In the location where the bath meets the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is very important as the installation can move enough to split a rigid seal, causing the water to permeate the wall surface in between the bath as well as the tiling, causing complications with dampness as well as feasible leakages to the ceiling below.
You can choose from a range of coloured sealers to assimilate your components and fittings. They are offered in tubes and cartridges, as well as can securing voids up to a width of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with spins of drenched paper or soft rope. Remember to always fill the tub with water before securing, to enable the activity experienced when the bathtub remains in usage. The sealer can crack fairly early if you do not consider this motion before securing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently readily available on the marketplace. It is suggested to fit the floor tiles making use of waterproof or water-proof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been shown that article about Tools You Need to Install a New Bathtub from an associate on our other web page. Sharing is good. Helping others is fun. Thank-you for taking the time to read it.
This Page
Report this page